Telex C-2002 Manuel d'utilisateur Page 9
- Page / 60
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Remote Control Console 3
Line Buttons LN1-LN2: Three buttons are available for each Line, SELect, RLS (Release) and Mute.
SELect button: When the SEL buttons is pressed that line enters the Select mode
Select LED: The Red LED under each LNx SEL Button indicates if the line is selected for transmit audio.
RLS button: The RLS button is used to release a selected line.
RLS LED: The blinking Red LED under each LNx RLS Button indicates receive audio activity on that line.
Mute button: The Mute button is used if RX audio from that line is not to be monitored in the speaker.
Mute LED: The steady Red LED under each LNx Mute Button indicates if the line is muted from receive
audio monitoring. A blinking LED indicates a external cross-mute.
Volume Control: Adjusts the receive speaker audio and handset earpiece level of the receive inputs of the line
interfaces. A minimum volume level can be set in tech-mode, so that the console operator cannot turn the speaker
volume to zero. When adjusting the level up or down, the display shows the selected level on a relative scale.
Monitor: When the Monitor button is pressed a Monitor tone burst is sent out on the selected line. The Monitor
tone burst consists of a guard tone and function tone of 2050Hz. An LED indication lights for the duration of the
tone burst.
Intercom (IC): When the Intercom button is pressed and held down the C-2002 shall transmit audio without
activating the tone generator. Intercom is considered a PTT operation with the tone generator disabled.
Panel PTT Pushbutton: When pressed, audio from the panel microphone plus key–up tones will be sent to all
Selected lines.
Transmit LED: This LED lights when any PTT source is depressed keying up the console. It will also blink if a
2175 Hz tone is detected on the selected TX audio lines. This would indicate to the operator that another console is
currently transmitting on one of the selected channels.
2.2 Rear Panel Connections
Figure 2 shows drawing of the rear panel of the C-2002. Each of the ports shown is discussed in detail in the
following section.
2.2.1 Rear Panel Ports
Power Jack: The left most jack on the C-2002 is the Power Jack. The power supply that is included with the unit
plugs in to this location. It is a standard 2.5mm center positive plug and requires at least 12V to operate correctly.
PORT
A
UX
+12
GND
POWER
+12
DATA
PORT
LINE
1
LINE
2
Figure 2 Rear Panel Diagram
- Table of Contents 3
- 1 Introduction 7
- 2 Controls and Indicators 8
- Remote Control Console 3 9
- 2.2 Rear Panel Connections 9
- 4 Vega’s C-2002 10
- 3 Operation 11
- 6 Vega’s C-2002 12
- 4.2 FEATURE DESCRIPTION 12
- Remote Control Console 7 13
- 8 Vega’s C-2002 14
- Remote Control Console 9 15
- 4.3 Level Adjustments 15
- 5 Hardware Overview 16
- 6 Theory of Operation 17
- 7 Setup Mode 19
- 14 Vega’s C-2002 20
- Remote Control Console 15 21
- 7.2 Opening menu 21
- 7.3 Level Menu Screen 21
- 16 Vega’s C-2002 22
- Remote Control Console 17 23
- 18 Vega’s C-2002 24
- 7.4 System Settings Screen 24
- Remote Control Console 19 25
- 20 Vega’s C-2002 26
- Remote Control Console 21 27
- 22 Vega’s C-2002 28
- Remote Control Console 23 29
- 24 Vega’s C-2002 30
- Remote Control Console 25 31
- 26 Vega’s C-2002 32
- 7.6 Line Tone/Local Screen 32
- Remote Control Console 27 33
- 7.7 Mute Button 33
- 28 Vega’s C-2002 34
- Remote Control Console 29 35
- 7.9 Supervisor Enable 35
- 7.10 Alert Programming 35
- 30 Vega’s C-2002 36
- Remote Control Console 31 37
- 32 Vega’s C-2002 38
- Remote Control Console 33 39
- 8 Technical Documentation 40
- PCB ASSY, C-2002 MAIN BOARD 49
- Signatur 58
- Remote Control Console 35 59
- 10 Specifications 60
Produits connexes et manuels pour Interphones de porte Telex C-2002
(23 pages)Hampton Bay HBF1129P-258 manuals
Owner’s manuals and user’s guides for Unknown Hampton Bay HBF1129P-258.
We providing 1 pdf manuals Hampton Bay HBF1129P-258 for download free by document types: Instruction Manual
Commentaires sur ces manuels